How many BTU per square foot?
The short answer is 20 BTU per square foot for cooling and 30 for heating in a mixed climate. The useful answer is a range by climate zone, because the same square foot is a different load in Miami and Minneapolis.
The chart
These are the factors behind the BTU calculator. They assume an 8 ft ceiling, average insulation and average window area. Cooling and heating are listed separately because they are separate loads.
| Zone | Example cities | Cooling BTU/sq ft | Heating BTU/sq ft |
|---|---|---|---|
| Zone 1 — very hot | Miami FL, Honolulu HI, San Juan PR | 24 | 10 |
| Zone 2 — hot | Orlando FL, Houston TX, Phoenix AZ | 22 | 15 |
| Zone 3 — warm | Atlanta GA, Dallas TX, Los Angeles CA | 20 | 20 |
| Zone 4 — mixed | Philadelphia PA, Nashville TN, St. Louis MO | 18 | 25 |
| Zone 5 — cool | Boston MA, Chicago IL, Denver CO | 16 | 30 |
| Zone 6 — cold | Minneapolis MN, Milwaukee WI, Burlington VT | 15 | 35 |
| Zone 7 — very cold | Fargo ND, Duluth MN, Caribou ME | 14 | 40 |
| Zone 8 — subarctic | Fairbanks AK, Utqiaġvik AK | 13 | 45 |
Read the table as a starting point, not a specification. It is a house rule built around the 20 to 25 BTU per square foot that ENERGY STAR’s room chart works out to for an average room, moved by climate zone so that hot climates sit higher and cold climates lower on cooling.
Worked examples
1,000 sq ft in zone 4
Cooling: 1,000 × 18 = 18,000 BTU/h, or 1.5 tons. Heating: 1,000 × 25 = 25,000 BTU/h, which rounds to a 40,000 BTU/h furnace because that is the smallest standard output. That gap between the calculated 25,000 and the 40,000 you can buy is normal at the small end of the market.
2,000 sq ft in zone 2
Cooling: 2,000 × 22 = 44,000 BTU/h, or 3.7 tons, which rounds to a 4-ton unit. Heating: 2,000 × 15 = 30,000 BTU/h. The air conditioner is the larger machine, which is why a Florida house is built around cooling and a heat pump there is sized on the cooling load.
2,000 sq ft in zone 6
Cooling: 2,000 × 15 = 30,000 BTU/h, or 2.5 tons. Heating: 2,000 × 35 = 70,000 BTU/h, so an 80,000 BTU/h output furnace. Same house, same square footage, a completely different equipment list — and a completely different utility bill.
Where the 20 BTU rule comes from
The rule is old enough that its origin is hard to pin down, but it survives because it is close to right for the house most Americans live in: a post-war or late-twentieth-century house in a mixed climate, with moderate insulation, ordinary windows and 8 ft ceilings. If you take ENERGY STAR’s room chart and divide capacity by area, the middle bands land at about 20 to 25 BTU per square foot, which is the same neighbourhood.
The trouble is that “average” houses are a shrinking share of the stock. A 2020 build with R-49 in the attic, double glazing and a sealed envelope may need 30% less. A 1920 house with single glazing, no wall insulation and a converted attic may need 30% more. The rule cannot tell those apart, and that is the whole argument for a Manual J.
When to move up or down
Move up from the chart when the space has large unshaded west or south glass, a cathedral ceiling, a kitchen that is open to the living area, a lot of electronics, or a roof with no attic ventilation. Move down when the space is below grade, heavily shaded, newly built to a modern code, or has exterior shading and few windows.
The adjustments compound. A 400 sq ft west-facing studio with 12 ft ceilings and a kitchen can easily need twice the BTU of a 400 sq ft north-facing bedroom. That is not an argument for a bigger air conditioner in every room; it is an argument for calculating each room separately if comfort is the goal.
Room-by-room versus whole-house
A whole-house number is right when you are buying one system and the ducts are reasonably balanced. A room-by-room number is right when you are buying a mini-split, when one room is always uncomfortable, or when you are deciding whether a single head can serve an addition. The arithmetic is the same; only the boundaries change.
For a room, use the interior dimensions and include closets that share the cooled air. For a house, use conditioned floor area and exclude the garage, the unfinished basement and any porch that is not heated. If the basement is finished and conditioned, include it, but note that below-grade walls lose far less heat than above-grade walls, so the per-square-foot rule overstates a basement load.
The mistakes this chart cannot stop
The first is buying to the next size up “just in case”. Oversizing costs more to run, dehumidifies worse and short-cycles the compressor. The second is using the cooling number to size a furnace, or the other way round. The third is ignoring the ducts: a right-sized system on undersized ducts delivers less than its rating, and the contractor blames the equipment.
The fourth is treating a heat pump like a furnace. A heat pump’s capacity falls with outdoor temperature, so the tonnage that looks right at 47°F may be short at 5°F. The heat pump calculator shows the gap and the backup heat it implies.
What to do with the number
Use it to sanity-check a quote, to choose between two sizes, or to decide whether a window unit or a mini-split is enough. Then ask for a Manual J before signing. The report should list every room, the window and wall areas, and the sensible and latent loads, and it should be free with a serious quote.
If you want the arithmetic done for you, the BTU calculator applies the ceiling, insulation, window, people and kitchen adjustments. The tonnage calculator converts the result to a size you can buy.
Frequently asked
How many BTU per square foot do I need?
For cooling, plan on 24 BTU/sq ft in zone 1, 22 in zone 2, 20 in zone 3, 18 in zone 4, 16 in zone 5, 15 in zone 6, 14 in zone 7 and 13 in zone 8, for an average house. For heating the figures run from 10 BTU/sq ft in zone 1 to 45 in zone 8.
Is 20 BTU per square foot accurate?
It is a reasonable average for a mixed climate and average construction, which is why it is repeated so often. It is too high for a new, tight house in a cool climate and too low for a glass-heavy house in a hot one. The zone chart narrows the error but does not remove it.
How many BTU for a 12 × 12 room?
A 144 sq ft room at 20 BTU/sq ft is 2,880 BTU/h, which is below the smallest window unit. In practice a 5,000 BTU/h window unit is the right purchase, and the extra capacity is the price of standard sizes, not a design choice.
Do I use the same number for heating and cooling?
No. Heating and cooling loads are different and peak at different times. A house in zone 5 has a cooling factor of 16 and a heating factor of 30, so the furnace is roughly twice the size of the air conditioner in BTU terms.
Does ceiling height change BTU per square foot?
Yes. BTU per square foot assumes an 8 ft ceiling. A 10 ft ceiling holds 25% more air and needs about 25% more capacity; a 12 ft ceiling about 50% more. The calculator applies this factor automatically.
Why do online charts disagree?
They assume different construction, different ceiling heights and different design temperatures, and many are copied from each other without saying so. A chart is a starting point; a Manual J is the answer for a specific house.
Where these numbers come from
- Room Air Conditioners — sizing chart and adjustments — U.S. EPA ENERGY STAR, read Nov 20, 2026
- ACCA Technical Manuals — Manual J, S, D and H — Air Conditioning Contractors of America (ACCA), read Nov 20, 2026
- Insulation — recommended R-values by climate zone — U.S. Department of Energy, Energy Saver, read Nov 20, 2026
- Furnaces and Boilers — U.S. Department of Energy, Energy Saver, read Nov 20, 2026
Numbers that come from our own arithmetic rather than a published table are marked house rule on the method page. No price appears anywhere on this site: no supplier publishes a national one, and an invented number would be worse than no number.
Next: BTU calculator · AC tonnage chart · window AC sizing · method and sources